openssl-dgst - perform digest operations
openssl dgst|digest [-digest] [-help] [-c] [-d] [-debug] [-list] [-hex] [-binary] [-xoflen length] [-r] [-out filename] [-sign filename|uri] [-keyform DER|PEM|P12|ENGINE] [-passin arg] [-verify filename] [-prverify filename] [-signature filename] [-sigopt nm:v] [-hmac key] [-mac alg] [-macopt nm:v] [-fips-fingerprint] [-engine id] [-engine_impl id] [-rand files] [-writerand file] [-provider name] [-provider-path path] [-propquery propq] [file ...]
This command output the message digest of a supplied file or files in hexadecimal, and also generates and verifies digital signatures using message digests.
The generic name, openssl dgst, may be used with an option specifying the algorithm to be used. The default digest is sha256. A supported digest name may also be used as the sub-command name. To see the list of supported algorithms, use openssl list -digest-commands
Print out a usage message.
Specifies name of a supported digest to be used. To see the list of supported digests, use the command list --digest-commands.
Print out the digest in two digit groups separated by colons, only relevant if the -hex option is given as well.
Print out BIO debugging information.
Prints out a list of supported message digests.
Digest is to be output as a hex dump. This is the default case for a "normal" digest as opposed to a digital signature. See NOTES below for digital signatures using -hex.
Output the digest or signature in binary form.
Set the output length for XOF algorithms, such as shake128.
Output the digest in the "coreutils" format, including newlines. Used by programs like sha1sum(1).
Filename to output to, or standard output by default.
Digitally sign the digest using the given private key. Note this option does not support Ed25519 or Ed448 private keys. Use the openssl-pkeyutl(1) command instead for this.
The format of the key to sign with; unspecified by default. See openssl-format-options(1) for details.
Pass options to the signature algorithm during sign or verify operations. Names and values of these options are algorithm-specific.
The private key password source. For more information about the format of arg see openssl-passphrase-options(1).
Verify the signature using the public key in "filename". The output is either "Verified OK" or "Verification Failure".
Verify the signature using the private key in "filename".
The actual signature to verify.
Create a hashed MAC using "key".
The openssl-mac(1) command should be preferred to using this command line option.
Create MAC (keyed Message Authentication Code). The most popular MAC algorithm is HMAC (hash-based MAC), but there are other MAC algorithms which are not based on hash, for instance gost-mac algorithm, supported by the gost engine. MAC keys and other options should be set via -macopt parameter.
The openssl-mac(1) command should be preferred to using this command line option.
Passes options to MAC algorithm, specified by -mac key. Following options are supported by both by HMAC and gost-mac:
Specifies MAC key as alphanumeric string (use if key contain printable characters only). String length must conform to any restrictions of the MAC algorithm for example exactly 32 chars for gost-mac.
Specifies MAC key in hexadecimal form (two hex digits per byte). Key length must conform to any restrictions of the MAC algorithm for example exactly 32 chars for gost-mac.
The openssl-mac(1) command should be preferred to using this command line option.
Compute HMAC using a specific key for certain OpenSSL-FIPS operations.
See "Random State Options" in openssl(1) for details.
See "Engine Options" in openssl(1). This option is deprecated.
The engine is not used for digests unless the -engine_impl option is used or it is configured to do so, see "Engine Configuration Module" in config(5).
When used with the -engine option, it specifies to also use engine id for digest operations.
See "Provider Options" in openssl(1), provider(7), and property(7).
File or files to digest. If no files are specified then standard input is used.
To create a hex-encoded message digest of a file: openssl dgst -md5 -hex file.txt
To sign a file using SHA-256 with binary file output: openssl dgst -sha256 -sign privatekey.pem -out signature.sign file.txt
To verify a signature: openssl dgst -sha256 -verify publickey.pem \ -signature signature.sign \ file.txt
The digest mechanisms that are available will depend on the options used when building OpenSSL. The openssl list -digest-commands command can be used to list them.
New or agile applications should use probably use SHA-256. Other digests, particularly SHA-1 and MD5, are still widely used for interoperating with existing formats and protocols.
When signing a file, this command will automatically determine the algorithm (RSA, ECC, etc) to use for signing based on the private key's ASN.1 info. When verifying signatures, it only handles the RSA, DSA, or ECDSA signature itself, not the related data to identify the signer and algorithm used in formats such as x.509, CMS, and S/MIME.
A source of random numbers is required for certain signing algorithms, in particular ECDSA and DSA.
The signing and verify options should only be used if a single file is being signed or verified.
Hex signatures cannot be verified using openssl. Instead, use "xxd -r" or similar program to transform the hex signature into a binary signature prior to verification.
The openssl-mac(1) command is preferred over the -hmac, -mac and -macopt command line options.
The default digest was changed from MD5 to SHA256 in OpenSSL 1.1.0. The FIPS-related options were removed in OpenSSL 1.1.0.
The -engine and -engine_impl options were deprecated in OpenSSL 3.0.
Copyright 2000-2021 The OpenSSL Project Authors. All Rights Reserved.
Licensed under the Apache License 2.0 (the "License"). You may not use this file except in compliance with the License. You can obtain a copy in the file LICENSE in the source distribution or at https://www.openssl.org/source/license.html.